HomeMy WebLinkAboutZ-5397 Map 3GENERAL ;DOTES
1. contractor shall protect all walls, doors, frames, surfaces,
fixtures, etc. scheduled as "existing to remain" from damage
dur'_ng demolition. Contractor shall verify if these
surfaces are plumb, square, and true and correct as
required.
2. Contractor shall take whatever precautions are necessary to
protect existing utility lines, ductwork, fixtures,
finishes, etc. which remain as oart of the final systems.
Contractor shall clean, repair, relamp, etc. these items as
required for proper functioning of the final sys_�m-
3. Contractor shall remove all items not indicated on
Construction Documents to remain, including, but not limited
to partitions, ducts, conduits, etc. which are not part of
the final system.
4. Contractor shall verify all dimensions before start of
construction and job conditions and shall report to a Twin
City Bank Representative any discrepancies or omissions
whicn would interfere vita satisfactory completion of work.
Contractor is responsible for verification of all field
measurements, field construction, and installation criteria,
coordination of all trades and owner supplied items, and the
means and methods of construction. Contractor is
responsible for arranging parking, etc. or the handling of
materials.
5. Contractor to oversee cleaning and ensure that the premises
are maintained free of rubbish during construction. Final
cleanup is the responsibility of the Contractor. Repair,
patch, touch-up or replace marred surfaces and maintain
cleaning until occupied by Twin City Bank.
6. At t..^,e termination of work, submit to Twin City Bank,
maintenance manuals presenting full details for care and
maintenance of all surfaces and equipment of every nature.
Contents shall include manufacturers' and installers' names,
addresses, and phone numbers, and instructions for instal-
lation, start-up, operation, maintenance parts list, and
data sheets.
Contractor is responsible for compliance with all codes,
ordinances, and regulations applicable at project location.
Contractor is responsible for filing and securing all
necessary permits, approvals, etc. for all trades.
9. Contractor shall be fully responsible for keeping abreast of
construction progress, and where delays have occurred due to
Contractor's fault, make up the lost time at this own
expense as necessary to maintain the contract schedule.
9. Contractor shall submit to Twin City Bank a bi-weekly job
status report. The report shall state actual progress of
the job, list any changes and any other conditions within
the scope of the Contract Documents affecting job progress.
10. Nuisance type work '.a. lack hammer, elec. shut down, etc.
should be scheduled to create the least tenant. annoyance.
11. Remove, store and reuse doors where applicable in existing
lease area. See plans for location (match existing hardware.
See millwork notes.) -
12. Contractor is required to meet all mechanical., electrical,
and plumbing specifications as specified by building
engineers along with HVAC as spec' -lied. -
rro rEr-Ty U NE
>0
MILLWORK NOTES C) N
1. All hardwood finished lumber and veneer plywood to be natural _ � C\J
plain sliced unless otherwise noted. Al'- joints to be
carefully and neatly made, surfaces straight and clean, work
C �
sanded with grain, grain continuous, and all machine marks Cc Q
removed by sanding. All cross scratches shall be eliminated. I% SEwI�E DRIVE q DO, -K ALT ;r `I LO
Connections shall be made by best approved practice of the - - -�.
cabinet making trade, including dadoes, dowels, mortises, and Q
C)
tenons where possible. Scribing, mitering, and joining shall_ —-------
�
be done accurately and neatly. Blind nail or blind screw
where possible_ All exposed nail 'holes to be filled in
preparation for finish. All exposed screws to be countersunk U
and plugged to match. h-- r
2. All surfaces scheduled to receive plastic laminate to receive I 1\ a%
laminate backing. Laminate surfacing shall be one continuous j
piece as :ouch as possible. J
3. Millwork Contractor to supply cabinet doors with self-closing __ ,�f �/
concealed casework hinges and drawers with full extension EXPANSION AREA
drawer slides unless unless othe r•wise noted. -
4. Field verify all millwork dimensions prior to fabrication and
installation. r `
5. All millwork material, finish hardwood, and veneer to be of
AWI (Architectural Woodwork Institute) "Custom Grade" and (\\
finishing based on AWI custom specs. Stain and oil finish to
match sample. \
6. Door and drawers to have taped or hard edges. Material to be `y
birch plywood with particle board acceptable on interior I � ET• ALN T " rte`
surfaces. Paint all interior surfaces. F=H \ F{ANDGAP?ED 12A4IPAN0
4pv Y re�iN;1pa1A +L K- AL -T.-4 2 Qi
7. Hinges semi consealed. Slides KV 1300 (length as required). mit`? uEt2.
Pulls - Stanley - staple type similar to 4483 verify finish
with owner.
8. Provide shelf standards and supports as noted.
9. Field measure all openings before construction.
8 s !'AeKIN�
LoT JZEpA1K iNGL. LGNTIW�
PARTITION NOTES
ALT *11
1. General Contractor to ensure that all walls and studs are
tied into structural members and/or slab above as required
to be safe and secure. Support laterally and seismically as
required by apo licable building codes. I -It
�
2. All drywall partitions to be straight, true, and plumb in I alp E(JALK IO
flat even planes, without waviness or cracks. Use special
care in providing true and flat surfaces for final finish by
other building trades including painting, wall covering, Uresilient base, base, millwork, and trim.
3. Provide mud -in type L -metal (USG Metal Trim 200A or approved I P U I� r
equal) for all exposed edges of gypsum wallboard surfaces 1i U
•J'GaG
and where wallboard abuts other materials.
4. Provide - 2 hr. rated wall around perimeter of lease space {� V
- full height floor to deck. Seal around beams or columnsI,`f
or adjacent there to. Provide 2 - layer 5/8" Type X each
side wall. (See plans for location) I
,i .�.G'`"4,<Y'127('Z '3 `•IIsi'" �-��':�'1.:J
rrl ocl r=iG,4•f"Io�:S �1E�S�..ARY o
e+' YVN cN
DRf} V`1 I KFS.
L. At O 7 ES 'b 5r--- gjaM0'- =D
,�SYyN ON JI/VI`v�6.
�.,) �C� sc�+i7 GONPpCT �cS
µp.h,DIcAPnE� !zi�N�R
8
z1-
�MD`JE T IE5 �:12AI ILS.
r�r7� „ �xIST• f'a+�urLs hr�..
T—
ZC9 � 0_+
IziN
�XI�(fh+C� Pa,eK�Nc>
� �i9f"'Pi.� je1l�V�lry LO}•�1PPGT ��Ra �� �� GoNGI�E-jE--J�
L Exlgfl NG RA1 6! D ___ GAJ �6 v �otF�i' -
-7,-
I
�q,nn v I � '1 "I � M '• I �L ,
----�,r2A L
�(
Ma?644' Exi 4
I-5
. DELETE ALT 42
p
EXIST; v6 o%ALK
GES I'j A>l -OC•ATIOH
AAIR5 iOUGPE
AftEA
c)
4
OC
V'
¢
W
z
Z
Y
z
U
Q
O
Q
Q
0
W
Q
mw
Z¢
OO
`
Z
�>
¢
Z
4z
O
Wcrp
w
z
�o
¢
QW
3:
H
�O_J
X(Y
Q.0—�
DATE:
PROJECT NUMBER:
op " 64&
SHEET TITLE
<�;7 17a �LAN%
SHEET NUMBER:
AI
SHEET I OF