HomeMy WebLinkAbout20170609_TR_Brian Minyard_Fassler Hall_Historic Commission Submission
To: Department of Planning and Development
723 West Markham Street
Little Rock, AR 72201
From: James Sullivan for AMR
Date: 06.09.17
Project: Fassler Hall ‐ LR
Attn: Brian Minyard
We are sending you the following items:
AAttttaacchheedd UUnnddeerr
SSeeppaarraattee CCoovveerr
PPllaannss SSppeecciiffiiccaattiioonnss CChhaannggee OOrrddeerr
SShhoopp DDrraawwiinngg SSuubbmmiittttaallss //
PPrroodduucctt DDaattaa
PPrriinnttss SSaammpplleess OOtthheerr
Copies: Date: Number: Description: Note:
01 Revised Drawings for Historic Commission – 24 x 36
12 Revised Drawings “ “ “ – 11 x 17
13
Exterior Light Fixture Cutsheets
Please see the following attached letter.
Thank you,
James Sullivan
NOTES:
Retain one copy of approved shop drawings & submittals for the Owner’s Close‐out documents.
06/09/17 REVISED DRAWINGS FOR HISTORIC COMMISSION
Brian,
The following changes have been made to the design since our last submission:
The exterior patio has changed:
o The overall area of the patio has increased from 2,737SF to 6,350SF.
The previously area was approximately 22’ wide and 140’ long along the west side of the building.
The south half of that 140’ (approximately) now extends west to Cumberland Street in the new
layout.
o A portion of the patio is raised 1’ higher than the existing asphalt, and surfaced with compacted granite
fines.
o The perimeter fence has changed from a wood-clad base with ornamental metal posts and rails to a skim
coated painted cmu base with cedar posts and horizontal slat rails.
o 2” x 1-1/2” steel posts will mount along the perimeter fencing spaced approximately 10’ apart to allow for the
suspension of string lights above the patio.
o The height of the majority of the fencing has reduced from 6’ to 4’-6” tall.
At the southeast corner of the patio, a portion of the fencing will need to increase to approximately
13’-1” in order to fully conceal mechanical equipment.
The West elevation has changed:
o The new openings along the façade have reduced from (3) 12’ wide by 10’ tall sections of storefront with 4
swinging doors each to (1) 12’-6” x 10’-3” section, (1) 6’-6” x 10’-3” section, and (1) 4’ x 8’ sliding window.
o The awnings above the new openings have changed from wood clad with painted letters to light aluminum
frame fabric awnings with printed letters.
o The diamond-patterned mural at the south end has shifted slightly to appear more continuous as it crosses
over the new mechanical yard fencing.
o (3) previously proposed goose neck light fixtures at the south end of the façade will now be totally
concealed by the tall mechanical yard fence, and replaced with (1) LED wall pack light fixture.
The East elevation has changed:
o The previously proposed (3) overhead doors have been eliminated, and the existing windows will remain.
o The existing overhead door will be exchanged for a smaller overhead door, and adjacent swinging door to
all fit within the existing overhead door opening.
o An additional swinging door has been added towards the south end of the building for code-required
egress.
o A kitchen hood exhaust fan has been positioned towards the south end of the façade.
o (13) previously proposed goose neck light fixtures along the façade have been replaced with (3) LED wall
packs.
Please note the alley is no longer being programmed as an outdoor patio.
The North elevation has changed:
o We propose to leave the alley gate the black ornamental metal fence it currently is.
o The sign above the entrance has changed from a suspended wood sign, to vinyl letter mounted to the
glass.
o The previously proposed metal screen has been eliminated
o The proposed metal letters will be backlit with concealed LED strips.
Thank you,
James Sullivan
SBREFURBISH EXISTINGWINDOWS. REPAIR /REPLACE BROKEN/DAMAGED GLASS,SEALANT, ETCAS NECESSARY6'-6"12'-6"EQ EQ EQ EQ EQEQ EQ EQ EQ EQ EQ EQCOMPACTED GRANITE FINESOVER GRAVEL - 1'-0" HIGH TOTALSTACKED STONE PAVERSTEPS W/ PTD MTLHANDRAILS EA SIDE &CENTERCAST CONCRETE RAMPW/ PTD MTL HANDRAILSEA SIDE1:12 SLOPE MAX12'-0"1:12 SLOPE MAX12'-0"EXISTING LANDSCAPE AREA@ ORIGINAL GRADEPOURED CONCRETELANDING & RAMP W/PTD MTL HANDRAILS EA SIDEEXISTING & NEWLYPATCHED ASPHALT- PAINT SURFACE64'-0 3/8"66'-4 1/4"64'-8"26'-0"+ 1' - 0"0' - 0"RUN THIS LEGOF FENCING SOUTHTO EXISTING FENCEEXISTING GAS METER- SEE MECH FORFINAL LOCATIONSEE SHEET A4.1 FORINFORMATION ON NEW FLOORSLAB IN ELEV LOBBYSTEEL STAIRCONC. PANNOTE:1. DIMENSIONS TAKEN FROM FACE OF EXISTING WALLS OR FACE OF STUD.2. REFER TO PLUMBING AND ELECTRICAL DRAWINGS FOR EQUIPMENT REQUIREMENTSDASH INDICATESSTRING LIGHTS-SEE ELEC.EQBUILDING NOTIN SCOPE70'-8 1/2" 21'-7 5/8" 49'-11 5/8"7'-6 3/8" 26'-2"20'-3 5/8"148'-9 7/8"PROJECTBUILDINGPROJECTPATIOENTRANCEMECHANICALYARDBAR IS ONE INCH ON ORIGINAL DRAWING..ONTS77CRCETIHC.RASNAKRAERGMAAARCHITECTS, INC.IF NOT ONE INCH ON THIS SHEETADJUST SCALES ACCORDINGLYBAR IS ONE INCH ON ORIGINAL DRAWING01"100 River Market Ave St. 301Little Rock, AR 72201501.375.0378 T501.375.6601 FProject:Location:Date:Title:Sheet Number:VERIFY SCALEFASSLER HALL - LITTLE ROCK311 E CAPITOL AVE, LITTLE ROCK, AR 7220201/13/2017FLOOR PLANHC_A1.01Revision History# Date Description01 03/07/17 ASI-01SCALE: 1/8" = 1'-0"1FIRST FLOOR PLAN_HCN
FIRST FLOOR0"SECOND FLOOR13' - 10"ROOF27' - 8"THOROLASTIC WALL COATINGOVER ENTIRE BRICK SURFACEDECORATIVE WALL STENCILING & PAINT;PAINT OVER THOROLASTICPAINT PATTERN OVEREXISTING DOOR & FRAMEINFILL REMOVED WINDOWW/ BRICK & PAINT TO MATCHREPAIR STUCCOAT BASEREPAIR STUCCO &DOWNSPOUT AT BASEREPAIR STUCCO AT BASEREPAIR STUCCO BASE AT PILASTER& BRICK AT DOOR FRAMEREPAIR DEEP CRACKIN STUCCOEXISTING ELEC. CONDUITPAINT TO MATCH WALL-REFER TO ELEC. PLANFOR SELECTIVE DEMOREMOVE EXIST'G VENTS& PATCH HOLES W/ MTL. PLATE-PAINT TO MATCH WALLEXHAUST FANSEE MECH.EXISTING DOORTO REMAINNEW 3X7 METALEXIT DOOREXISTING WINDOWS TO REMAIN& BE REPAIRED AS NEEDEDNEW OVERHEAD & SWINGDOOR TO BE INSERTED INEXISTING OVERHEAD DOOROPENINGLED WALL PACK LIGHTLED WALL PACK LIGHTLED WALL PACK LIGHTFIRST FLOOR0"SECOND FLOOR13' - 10"ROOF27' - 8"11 GAUGE CUSTOM CUT METAL LETTERS;WALL MOUNTED W/ STL. ANGLE BOLTEDINTO HORIZONTAL BRICK JOINTS.BACKLIT; SEE ELEC5'-3"22'-8"NEW STOREFRONTDOORS IN EXISTINGSTOREFRONT SYSTEMEXISTING BRICK TO REMAINTUCKPOINT & PROVIDE CLEARWATER REPELLANT COATINGEXISTING STOREFRONT & CURTAIN WALL TO REMAIN;REPAIR, CLEAN & POLISH.ADJACENT BUILDING& SOLID BRICK FENCE(DASHED) -NOT IN SCOPEPROJECT FENCING BEYOND(LIGHT LINES)STRING LIGHTS; SEE ELECREPLACE THIS PANEDUE TO CRACKED GLASSREPLACE THIS PANEDUE TO CRACKED GLASSREPAIR STUCCOAT BASESCRAPE AWAY PEELINGPAINT & REPAINT ALL WHITESTUCCO & CONCRETE-TYP AROUND BUILDINGVINYL LETTERS &NUMBERS ON GLASSEXISTING METAL GATETO REMAINHORIZONTAL PLANK CEDAR FENCE.CMU BLOCK BASE TO BE SKIM COATED& PAINTED IN RAISED EXTERIOR AREAS; SEE PLANSMETAL CLAD CANOPYW/ SOFFIT CAN LIGHTINGFIRST FLOOR0"SECOND FLOOR13' - 10"ROOF27' - 8"THOROLASTIC WALL COATINGOVER ENTIRE BRICK SURFACEDECORATIVE WALLSTENCILING & PAINT; PAINTOVER THOROLASTICFIRST FLOOR0"SECOND FLOOR13' - 10"ROOF27' - 8"BASF THOROLASTIC WALL COATINGON ALL BRICK AT SOUTH, EAST, & WESTELEVATIONS; STANDARD COLORDECORATIVE WALL STENCILING &PAINT; PAINT OVER THOROLASTICDECORATIVE WALL STENCILING &PAINT; PAINT OVER THOROLASTIC(OR OTHER WEATHERPROOFING) LAYERSALUM FRAME FABRIC AWNINGS W/LETTERING @ FRONT VALANCENEW ALUM STOREFRONT DOORS& TRANSOM SYSTEMNEW SLIDING STOREFRONTWINDOW - SEEEQ EQEQ EQEQ EQNEW WALL MOUNTEDLIGHT FIXTURESEXISTING GASMETERREMOVE EXISTINGLIGHT FIXTURE& PATCH BRICKREMOVE AIR UNIT & INFILL W/BRICK -PAINT TO MATCHSLIDESLIDE8 / A2.01TO CONCEAL MECH EQUIP13'-1" AFFEXISTING STOREFRONT & CURTAIN WALL TO REMAIN;REPAIR, CLEAN & POLISH.STOP STENCILING BEHINDFENCE11'-0"14'-9 1/4"6'-0"7'-6"14'-7 3/4"10'-4 3/4"16'-11"6'-10"8'-0"12'-6"10'-3"6'-6"8'-0"3'-6" 4'-0"TOP OF FENCE LINEBEYOND (DASHED)LED WALL PACKLIGHT FIXTUREINSIDE ENCLOSUREADJACENT BUILDING AND SOLID BRICKFENCE (DASHED) - NOT IN SCOPEPROJECT BEYOND (LIGHT LINES)BAR IS ONE INCH ON ORIGINAL DRAWING..ONTS77CRCETIHC.RASNAKRAERGMAAARCHITECTS, INC.IF NOT ONE INCH ON THIS SHEETADJUST SCALES ACCORDINGLYBAR IS ONE INCH ON ORIGINAL DRAWING01"100 River Market Ave St. 301Little Rock, AR 72201501.375.0378 T501.375.6601 FProject:Location:Date:Title:Sheet Number:VERIFY SCALEFASSLER HALL - LITTLE ROCK311 E CAPITOL AVE, LITTLE ROCK, AR 7220201/13/2017EXTERIOR ELEVATIONSHC_A2.01Revision History# Date DescriptionSCALE: 1/8" = 1'-0"3EAST ELEVATION_HCSCALE: 1/8" = 1'-0"5NORTH ELEVATION_HCSCALE: 1/8" = 1'-0"4SOUTH ELEVATION_HCSCALE: 1/8" = 1'-0"1WEST ELEVATION_HCSCALE: 1/8" = 1'-0"2WEST ELEVATION 2_HC
FIRST FLOOR0"1'-0"6"1'-0"1'-6"3'-0"6" STACKEDSTONE PAVERSPTD METAL HANDRAILBEYOND-SET IN CONCRETECOMPACTED GRANITEFINES OVER GRAVEL1'-0" HIGH TOTALEXISTING ASPHALTPARKING LOTGRT FINES OVER GRVL1'-0"1'-0"OVERLAP6"3'-6"FIRST FLOOR0"2" CMU CAPCMU BLOCKW/ REBAR & FILLW/ MORTAR-SEE STRUC FORLOCATIONSGALV HSS 2X1 1/2-REFER TO STRUC.STRING LIGHTS; SEE ELECSTRIKE MORTAR JOINTSFLUSH @ ALL BLOCK WALLS-TYPCEDAR 6 X 6 POSTCEDAR 1 X 6 PLANKW/ 1/2" SPACING1X CEDAR PLANK CAPCOMPACTED GRANITEFINES OVER GRAVEL1'-0" HIGH TOTALEXISTING ASPHALTPARKING LOT1'-0"1/4" PLATE W/ ADHESIVE POSTANCHOR SYSTEM-REFER TO STRUC.4'-6"2'-0"T.O. STL. POST11'-0"1/2"CONCRETE PIER@ 2'-8" O.C.-REFER TO STRUC.8"8"2"CEDAR 6 X 6 POST1/4" PLATE W/ ADHESIVE POSTANCHOR SYSTEM-REFER TO STRUC.GALV HSS 2X1 1/2-REFER TO STRUC.CEDAR 1 X 6 PLANKW/ 1/2" SPACINGBETWEEN BOARDS- PLANKS TO EXTERIORSIDE OF FENCE ONLYCOMPACTED GRANITEFINES OVER GRAVEL1'-0" HIGH TOTALEXISTING ASPHALTPARKING LOTCORRUGATED METALROOF; SEE STRUCTURAL1/2" BOLT FASTEN TO STUDS &METAL PANELS; ADJUST LENGTH BOLTLENGTH TO MAINTAIN LEVEL SOFFITCONT. PRE-FIN MTL FASCIACAN LIGHTS; SEE ELEC.CUT OPENING THRU PERF PANELS.EXISTING STOREFRONTEXISTING STUCCO FASCIA1" ROUND PERFORATED METALSOFFIT PANEL W/ 1/2" METAL WELDEDEDGE BANDING - PAINTEDSLOPE 1/4" PER FT MINMETAL STUD FRAMING;SEE STRUCTURAL FOR MEMBERS& FASTENING. SIDE STUD TRACKSTO SLOPE AGAINST BUILDING.1'-0"5'-0"4"REPLACE EXISTING GLASSWITH SPANDREL GLASSPANELS AT CENTERSECTION ONLYEXISTING STOREFRONTMETAL Z-FLASHING OVER STUCCO& ONTO METAL ROOF. APPLY SEALANTINSIDE CORRUGATIONSPROVIDE CLOSURES AT THEEND OF THE CORRUGATIONMETAL L-FLASHING AGAINSTBRICK SIDES & ONTO METALROOF (DASHED). APPLY SEALANTINSIDE CORRUGATIONSAPPLY METAL PANEL AT WEST CANOPYSIDE WHERE THERE A GAP DUE TOSTOREFRONT STEPPING BACK. FULLYCONCEAL CANOPY CAVITY.FIRST FLOOR0"MAX4"1'-6"EXISTING WALLLED LIGHT STRIP; SEE ELEC.SCREW FIXTURE INTO BRICK@ MORTAR ONLY4 1/2"COUNTER SINK BOLTS THRU TREATED 1x BLOCKING &BRICK; MOUNT LIGHT FIXTURE TO BLOCKINGLED LIGHT STRIP; SEE ELEC.SCREW FIXTURE INTO BRICK@ MORTAR ONLYNOTE: THERE ARE (2) VERITCAL STRIPS @ 7'-6" LONG& (2) VERTICAL STRIPS @ 13' LONG2'-2"BAR IS ONE INCH ON ORIGINAL DRAWING..ONTS77CRCETIHC.RASNAKRAERGMAAARCHITECTS, INC.IF NOT ONE INCH ON THIS SHEETADJUST SCALES ACCORDINGLYBAR IS ONE INCH ON ORIGINAL DRAWING01"100 River Market Ave St. 301Little Rock, AR 72201501.375.0378 T501.375.6601 FProject:Location:Date:Title:Sheet Number:VERIFY SCALEFASSLER HALL - LITTLE ROCK311 E CAPITOL AVE, LITTLE ROCK, AR 7220201/13/2017EXTERIOR DETAILSA2.02SCALE: 1 1/2" = 1'-0"3EX. PATIO STAIR PAVERSSCALE: 1 1/2" = 1'-0"1EX. PATIO FENCE @ CMU WALLSCALE: 1 1/2" = 1'-0"2EX. PATIO FENCE POST - PLAN DETAILRevision History# Date Description01 03/07/17 ASI-01SCALE: 1 1/2" = 1'-0"4SECTION @ ENTRANCE CANOPYSCALE: 1 1/2" = 1'-0"5METAL LETTERS & PLAN DETAIL
Submitted by Malmstrom White CompanyJob Name: FASSLER HALLArchitect: AMR ARCHITECTS (LITTLEROCK)Engineer: JAMES PRIMM, PECatalog Number:QS-4W-O-100IN-120V-WM-STANDARD COLORNotes: Type: MWC17-7365ESTABLISHED 1923
Forte Wall Quickship
Specifications are subject to change without notice.
TMS Lighting Inc.
247A Summerlea Road,
Brampton, Ontario,
Canada. L6T 4E1
Web Site: tmslighting.com
North America: (905) 793-1174
Toll-free: (866) 793-1174
Fax: (905) 793-1175
UK & Europe: 44-1474-250-654
Custom
TMS Lighting can customize this and many of our standard fixtures. The dimensions, lamp types, enclosure
and colors could be modified to suit your lighting and architectural requirements. Contact your local
representative for more details: http://tmslighting.com/info/agents
33.37” (848 mm)
18.62”
(473 mm)
16” dia.
(406 mm)
3.36”
(85 mm)
Optional LED Driver or
CF / MH Ballast
EXTERIOR LIGHT FIXTURE ALONG WEST ELEVATION
Submitted by Malmstrom White Company
Job Name:
FASSLER HALL
Architect: AMR ARCHITECTS (LITTLE
ROCK)
Engineer: JAMES PRIMM, PE
Catalog Number:
XTOR6BRL
Notes:
Type:
MWC17-7365
XTOR
CROSSTOUR
MAXX LED
APPLICATIONS:
WALL / SURFACE
INVERTED
SITE LIGHTING
Lumark
SPECIFICATION FEATURES
Construction
Low-profile LED design with
rugged one-piece, die-cast
aluminum back box and hinged
removable door. Matching housing
styles incorporate both a full cutoff
and refractive lens design. Full
cutoff and refractive lens models
are available in 58W and 81W.
Patent pending secure lock hinge
feature allows for safe and easy
tool-less electrical connections with
the supplied push-in connectors.
Back box includes four 1/2” NPT
threaded conduit entry points. The
back box is secured by four lag
bolts (supplied by others). External
fin design extracts heat from the
fixture surface. One-piece silicone
gasket seals door and back box.
Not recommended for car wash
applications.
Optical
Silicone sealed optical LED
chamber incorporates a custom
engineered reflector providing
high-efficiency illumination.
Full cutoff models integrate an
impact-resistant molded refractive
prism optical lens assembly
meeting requirements for Dark
Sky compliance. Refractive lens
models incorporate a molded lens
assembly designed for maximum
forward throw. Solid state LED
Crosstour MAXX luminaries are
thermally optimized with eight
lumen packages in cool 5000K or
neutral 4000K (58W, 81W models)
LED color temperature (CCT).
Electrical
LED driver is mounted to the
die-cast aluminum housing for
optimal heat sinking. LED thermal
management system incorporates
both conduction and natural
convection to transfer heat rapidly
away from the LED source. 58W
and 81W models operate in -40°C
to 40°C [-40°F to 104°F]. High
ambient 50°C [122°F] models
available in 58W and 81W models
only. Crosstour MAXX luminaires
maintain greater than 89% of initial
light output after 72,000 hours
of operation. Four half-inch NPT
threaded conduit entry points
allow for thru-branch wiring. Back
box is an authorized electrical
wiring compartment. Integral LED
electronic driver incorporates surge
protection. 120-277V 50/60Hz,
480V 60Hz, or 347V 60Hz electrical
operation. 480V is compatible for
use with 480V Wye systems only.
Emergency Egress
Optional integral cold weather
battery emergency egress includes
emergency operation test switch
(available in 58W and 81W models
only), an AC-ON indicator light and
a premium extended rated sealed
maintenance-free nickel-metal
hydride battery pack. The separate
emergency lighting LEDs are wired
to provide redundant emergency
lighting. Listed to UL Standard 924,
Emergency Lighting.
Area and Site Pole Mounting
Optional extruded aluminum 6-1/2”
arm features internal bolt guides
for supplied twin support rods,
allowing for easy positioning of the
fixture during installation to pole.
Supplied with round plate adapter
plate. Optional tenon adapter fits
2-3/8” or 3-1/2” O.D. Tenon.
Finish
Crosstour MAXX is protected with
a super TGIC carbon bronze or
summit white polyester powder
coat paint. Super TGIC powder coat
paint finishes withstand extreme
climate conditions while providing
optimal color and gloss retention
of the installed life.
Warranty
Five-year warranty.
TD514005EN
2016-12-13 15:58:28
The patented Lumark Crosstour™ MAXX LED wall pack series of
luminaries provides low-profile architectural style with super bright,
energy-efficient LEDs. The rugged die-cast aluminum construction,
back box with secure lock hinges, stainless steel hardware along with a
sealed and gasketed optical compartment make Crosstour impervious
to contaminants. The Crosstour MAXX wall luminaire is ideal for wall/
surface, inverted mount for facade/canopy illumination, perimeter and
site lighting. Typical applications include pedestrian walkways, building
entrances, multi-use facilities, industrial facilities, perimeter parking
areas, storage facilities, institutions, schools and loading docks.
DESCRIPTION
CERTIFICATION DATA
UL/cUL Wet Location Listed
LM79 / LM80 Compliant
ROHS Compliant
NOM Compliant Models
3G Vibration Tested
UL924 Listed (CBP Models)
IP66 Rated
TECHNICAL DATA
40°C Ambient Temperature
External Supply Wiring 90°C Minimum
EPA
Effective Projected Area (Sq. Ft.):
XTOR6B, XTOR8B=0.54
With Pole Mount Arm=0.98
SHIPPING DATA:
Approximate Net Weight:
12-15 lbs. [5.4-6.8 kgs.]
FULL CUTOFF DEEP BACK BOX DEEP BACK BOXREFRACTIVE LENS
8-3/4"[222mm]
8-3/4"[222mm]6-1/4"[159mm]7"[178mm]
6"[152mm]7"[178mm]
11 "[279mm]
11 "[279mm]
DIMENSIONS
Catalog # Type
Date
Project
Comments
Prepared by
Index Page
EXTERIOR LIGHT FIXTURE ALONG EAST ELEVATION & INSIDE
FENCED MECHANICAL YARD
Submitted by Malmstrom White Company
Job Name:
FASSLER HALL
Architect: AMR ARCHITECTS (LITTLE
ROCK)
Engineer: JAMES PRIMM, PE
Catalog Number:
LS-MS-24-BK, (330) LS-CABLE-
SPECIFY LENGTH, (5) LS-LOCK-4
Notes:
Type:
MWC17-7365
FEATURES
• Factory-molded sockets on 14-gauge wire is suitable for
commercial applications (16-gauge for kits)
• Formulated PVC sockets form a tight weatherproof seal
around the bulb
• Long life, low maintenance linear lighting (for use with
LED retrofits and Long Life Lamps – see pages 46-47)
• Available in bulk reels in candelabra, intermediate and
medium base sockets
• Use with LED lamps to run full reel length and save up to
98% in energy costs over incandescent
Light string CommErCiAL grADE
Use commercial grade light string with LED lamps to run
full reel length and save up to 80% in energy costs over
incandescent. suitable for decorative lighting, patio lighting,
tents, events, pavilions, sales lots and many overhead
perimeter lighting applications.
44 www.americanlighting.com
medium Base
max load/socket 25 watts
max load/socket 10 watts
intermediate Base
suspended medium Base
max load/socket 25 watts
Candelabra Base
max load/socket 10 watts
Popular, versatile, commercial grade light string
CommerCial grade Light string
Index Page
STRING LIGHTS HUNG FROM POLES ABOVE THE EXTERIOR PATIO
page 1 of 3 www.luminii.com tel: 224-333-6033REV 1.8
Kendo M Wet Graze Linear grazing system
Technical information
KMWG
MODEL
Ordering code
27K
27K - 2700 K30K - 3000 K40K - 4000 K45K - 4500 K
12
12”- 116”
4” increments
F1
F1 - 72” wire leadsF2 - 72” wire leads
at one end and quick
connect at otherF3 - Single quick connectF4 - Dual quick connect
Kendo M
Wet Graze
HO
HO - HighVHO - VeryHigh
20
20° - Semi-frosted
A
A - AdjustableF - Fixed
SA
LENGTH POWER FEEDOUTPUTCCTLENSMOUNTINGFINISH
SA - Silver
BK - Black
BZ - Bronze
WH - White
(BK,BZ,WH
finishes will have
an upcharge and
require longer
lead times)
Finish options
Black
powder coated
Bronze
powder coated
Silver
anodized
White
powder coated
Extruded aluminum linear grazing system, Kendo M Wet Graze features a 20° lightly frosted lens. Available in
sections up to 116” long, Kendo M Wet Graze is suitable for highlighting textured surfaces, stone walls or for edge
lighting. Class 2 listed for wet location installations.
0.79”
0.70”
90˚90˚
0.82”
0.93”
0.70”
Adjustable mounting bracket allows 90˚ tilt in
both directions.
0.94”
CRI (Typical)
Color
temperature
High
[+/- 75 K and single bin]
2700 K 90+
3000 K 90+
4000 K 90+
4500 K 90+
Output Options
Output type HO
(LL54)
VHO
(LL72)
Lumens at 3000K
High CRI 243 lum/ft 343 lum/ft
Average power
consumption at 4’5.2 W/ft 6.5 W/ft
Maximum system
length 26’18’
Operating Voltage 24VDC 24VDC
with fixed
mounting clips
0.70”
0.73”
CONCEALED EXTERIOR LIGHT STRIP AT METAL LETTERS ON NORTH FACADE